In Zephyr's Bluetooth Mesh PB-ADV provisioning bearer (subsys/bluetooth/mesh/pb_adv.c), prov_msg_recv() rescheduled the provisioning protocol watchdog timer unconditionally at the top of the function, before the FCS check and before the ADV_LINK_INVALID check. Once a provisioning attempt fails, prov_failed() sets ADV_LINK_INVALID and the only recovery path is the protocol timer firing (protocol_timeout -> prov_link_close -> close_link -> reset_adv_link and re-enabling of scanning and the unprovisioned device beacon). A remote, unauthenticated attacker on the BLE advertising channel can first induce a provisioning failure (e.g. with a malformed generic-provisioning PDU) and then transmit any FCS-valid PB-ADV transaction PDU on the same link ID more often than once per protocol timeout (60 s, or 120 s for OOB input/output). Because each such packet reset the timer even on an invalidated link, protocol_timeout never fired, the dead link was never torn down, and the device remained pinned in an un-provisionable state with its unprovisioned beacon disabled and new Link Open requests rejected. PB-ADV PDUs are processed without authentication and the FCS is a keyless CRC, so no pairing or prior trust is required and the attacker chooses the link ID itself. The impact is a persistent denial of provisioning/re-provisioning service; there is no memory-safety, confidentiality, or integrity impact. The vulnerable code shipped in releases through v4.4.1. The fix moves the timer reschedule to after the ADV_LINK_INVALID check (and the FCS check before the reset) so an invalidated link can no longer be kept alive by incoming packets.

The MCTP-over-I2C+GPIO target binding in Zephyr (subsys/pmci/mctp/mctp_i2c_gpio_target.c) processes pseudo-register writes from an I2C bus master byte-by-byte in mctp_i2c_gpio_target_write_received() without validating the order or the receive buffer. In the affected versions the MCTP_I2C_GPIO_RX_MSG_ADDR (data) handler dereferences and writes through b->rx_pkt without checking that the receive buffer was allocated: a controller that selects the data register and writes a byte without first sending the length register (which is what allocates the buffer) causes a write of an attacker-chosen byte through a NULL/unallocated mctp_pktbuf pointer (i.e. into a small attacker-advanceable offset above address 0), producing memory corruption or a hard fault. The same handler also performs a write-then-check bounds test, allowing a one-byte heap overflow at data[255] when more than 255 data bytes are sent. Because the I2C target callback is invoked with raw bytes supplied by whatever device is the bus master and the binding performs no authentication, a malicious or malfunctioning controller on the bus can trigger these without any prior protocol state, leading to memory corruption and/or denial of service on the target device. The vulnerable code was introduced when the I2C+GPIO target binding was added and shipped in Zephyr v4.3.0 and v4.4.0. The fix defers allocation to the first data byte with a NULL check, treats a missing length as a zero-sized packet rejected by libmctp, and moves the bounds check before the store.

The Classic (BR/EDR) L2CAP signaling handlers l2cap_br_conf_req() and l2cap_br_conf_rsp() in subsys/bluetooth/host/classic/l2cap_br.c validated the minimum command size against buf->len (the bytes remaining in the whole received PDU) instead of len (the per-command data length from the L2CAP signaling header). Because multiple signaling commands can be packed into one PDU, buf->len may exceed a command's len. An attacker can send a CONF_REQ command with a header length smaller than the configuration-request structure (e.g. 0), followed by another command so that buf->len still satisfies the check. The check then passes incorrectly and opt_len = len - sizeof(*req) underflows the uint16_t to a near-0xFFFF value. The configuration-option loop, which lacks an opt_len-versus-buf->len guard, then walks far past the end of the pooled ACL receive buffer using net_buf pull primitives that perform no runtime bounds check, producing an out-of-bounds read of host memory and, when the out-of-bounds option bytes encode an MTU or flush-timeout option, an out-of-bounds write. The BR/EDR signaling channel is processed before pairing/encryption and an L2CAP channel to an L0 service such as SDP can be opened without pairing, so an unauthenticated peer within radio range that can establish an ACL connection can trigger the flaw, leading to memory corruption and denial of service (host/device crash). The defect is present in released versions including v4.4.0. The fix validates against len instead of buf->len in both handlers.

The CONFIG_USERSPACE syscall verifier z_vrfy_k_poll() in kernel/poll.c allocates a kernel-side copy of the user-supplied k_poll_event[] via z_thread_malloc() and then validates each event's object handle. Before this fix, validation used K_OOPS(K_SYSCALL_OBJ(...)) inline inside the loop, which kills the calling thread without freeing events_copy. A user thread can pass num_events >= 1 with a forged object handle to leak the allocation; because newly spawned user threads inherit the parent's resource_pool (kernel/thread.c), an attacker spawns sacrificial threads to repeat the leak until the shared kernel heap is exhausted. Once depleted, legitimate kernel allocations from that pool (k_queue alloc nodes, k_msgq buffers, future k_poll calls, etc.) fail, causing a system-level denial of service. The fix replaces each inline K_OOPS with a conditional goto oops_free so the buffer is freed before the thread is killed. Affects Zephyr releases from v1.12.0 (when k_poll was first exposed to user mode) through v4.4.1.

The DesignWare SPI driver (drivers/spi/spi_dw.c) computed the SPI BAUDR clock divider as info->clock_frequency / config->frequency without validating config->frequency. spi_transceive is a Zephyr __syscall and its verify handler (drivers/spi/spi_handlers.c) copies the caller-supplied spi_config from userspace without checking the frequency field, so a userspace thread that has been granted access to a DesignWare SPI device kernel object can pass frequency = 0 and trigger an unsigned integer divide-by-zero in spi_dw_configure(). On Cortex-M Mainline (SCB->CCR.DIV_0_TRP is set in z_arm_fault_init()) and on ARC (a dedicated __ev_div_zero vector) this raises a CPU exception, resulting in a kernel fault and local denial of service. The fix rejects zero frequency and frequencies above clock_frequency / 2 (the DesignWare SSI databook minimum SCKDIV of 2) with -EINVAL. The defect affects all Zephyr releases up to and including v4.4.0; exploitation requires CONFIG_USERSPACE=y and an unprivileged thread already granted SPI driver permission. There is no memory-corruption or information-disclosure impact.

The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.

The CONFIG_USERSPACE verification handler for the k_thread_name_copy() system call (z_vrfy_k_thread_name_copy() in kernel/thread.c) calls k_object_find() on the caller-supplied thread pointer and then dereferences the returned struct k_object without checking it for NULL. k_object_find() returns NULL whenever the supplied pointer is not a registered (static or dynamic) kernel object. The pre-fix guard tested thread == NULL instead of ko == NULL, so an unprivileged user-mode thread that invokes k_thread_name_copy() with any non-NULL but unregistered pointer (e.g. an arbitrary address) passes the NULL test, after which the verifier reads ko->type through a NULL pointer. Because the syscall verifier runs in supervisor mode, this NULL dereference is a kernel-mode fault that halts or reboots the system, allowing untrusted user code to crash the kernel across the userspace security boundary (denial of service). The marshaller passes the thread argument to the verifier without any prior K_SYSCALL_OBJ validation, so the bad pointer reaches the defect directly. The flaw affects builds with CONFIG_USERSPACE and CONFIG_THREAD_NAME enabled and has been present since the special-case lookup was introduced around v2.0.0; it is present in v4.4.0 and earlier. The fix changes the guard to check the k_object_find() return value (ko == NULL) before dereferencing it.

subsys/net/lib/lwm2m/lwm2m_pull_context.c copied the firmware-update Package URI into a fixed static buffer (context.uri, size CONFIG_LWM2M_SWMGMT_PACKAGE_URI_LEN, default 128) with memcpy(context.uri, uri, LWM2M_PACKAGE_URI_LEN), copying exactly the destination size with no length validation. The Firmware-Update object stores the server-supplied Package URI (/5/0/1) in a 255-byte buffer, so a LwM2M management server (or an on-path attacker on a session lacking strong DTLS) can WRITE a URI of 128-254 characters; only the first 128 bytes are then copied into context.uri with no NUL terminator. That buffer is subsequently consumed as a C string by http_parser_parse_url(context.uri, strlen(context.uri), ...), strlen-based CoAP URI-path/PROXY-URI option appends, and lwm2m_parse_peerinfo(), causing an out-of-bounds read of adjacent static memory. The over-read bytes are appended to outbound CoAP requests (information disclosure of adjacent device memory to the server/proxy) and can crash the device (denial of service). The vulnerable copy was introduced by the pull-context refactor (first released in v3.0.0) and is present through v4.4.0; the default-on CONFIG_LWM2M_FIRMWARE_UPDATE_PULL_SUPPORT path is affected. The fix adds a strlen(uri) >= sizeof(context.uri) check returning -ENOMEM and switches to strcpy(), guaranteeing a bounded, NUL-terminated buffer.

Zephyr's dynamic kernel-object tracking (kernel/userspace/userspace.c, formerly kernel/userspace.c) maintains a doubly-linked list (obj_list) of dynamically allocated kernel objects. Iteration over this list in k_object_wordlist_foreach() was performed under lists_lock using the SAFE iterator (which caches the next node), but list removal and freeing of nodes was performed under different, disjoint spinlocks: objfree_lock in k_object_free() and obj_lock in unref_check(). On an SMP system, while one CPU iterated obj_list under lists_lock, another CPU could unlink and k_free() the dyn_obj node that the iterator had cached as its next pointer, causing the iterator to dereference freed kernel memory (use-after-free / dangling list traversal). All of the racing operations are reachable from unprivileged user-mode threads via system calls: k_object_alloc/k_object_alloc_size and k_object_release drive removals through unref_check() (under obj_lock), while k_thread_abort and thread creation drive the iteration through k_thread_perms_all_clear()/k_thread_perms_inherit() (under lists_lock). A deprivileged user thread on a CONFIG_SMP + CONFIG_USERSPACE build can therefore corrupt the kernel's object-tracking structures across the userspace security boundary, yielding kernel memory corruption (potential privilege escalation) or a kernel crash (denial of service). The fix removes objfree_lock and serializes every obj_list modification under lists_lock, including holding it across find+remove in k_object_free() and around unref_check() in k_thread_perms_clear(). Affects CONFIG_SMP+CONFIG_USERSPACE+CONFIG_DYNAMIC_OBJECTS configurations; the defect dates to the 2019 spinlockification (commit 8a3d57b6cc6, first released in v1.14.0) and shipped through v4.4.0.

The Nuvoton NuMaker HSUSBD USB device-controller driver (drivers/usb/udc/udc_numaker.c) armed the control Data IN stage unconditionally (base->CEPTXCNT = len in numaker_hsusbd_ep_trigger). Because the HSUSBD hardware cannot disarm a control Data IN already armed for a previous transfer, a USB host that cancels an in-flight control transfer (timeout) and then issues a new SETUP packet can drive the driver out of sync: stale data may be transmitted in the new transfer and the control endpoint can become permanently stuck NAK'ing every subsequent control transfer. A malicious or buggy host (physical/adjacent attacker driving the bus) can repeatedly cancel-and-re-SETUP to wedge the device's USB control endpoint, denying service to the device's USB function (the device stops enumerating/responding on the control pipe) until a USB reset or re-plug. The flaw is an availability-only denial of service; the FIFO copy loops (bounded by net_buf length and the hardware BUFFULL flag) and the net_buf lifecycle are independent of the arming desync, so there is no out-of-bounds access, use-after-free, or information leak. The fix monitors the IN-token and new-SETUP events (k_event) and only arms control Data IN when an IN token is present and no new SETUP has arrived, cancelling the current transfer on a new SETUP. Affects boards using the Nuvoton NuMaker HSUSBD controller (CONFIG_UDC_NUMAKER with DT_HAS_NUVOTON_NUMAKER_HSUSBD_ENABLED); shipped in v4.4.0.