In Splunk Connect for Kafka versions below 2.2.7, an unauthenticated user who can reach the Kafka Connect Representational State Transfer (REST) API could configure a non-secure Hypertext Transfer Protocol (HTTP) Event Collector endpoint in Splunk Enterprise that causes the connector to send authentication credentials to an attacker-controlled server, allowing for exposure of credentials that compromise all relevant data sent through the connector and limited alteration of event delivery. The vulnerability is possible because HTTP Event Collector endpoint validation does not require secure transport by default. For more information see Install Splunk Connect for Kafka (https://help.splunk.com/en/data-management/integrate-data-with-add-ons/splunk-connect-for-kafka/2.2/install/install-splunk-connect-for-kafka), Data ingestion parameters for Splunk Connect for Kafka (https://help.splunk.com/en/data-management/integrate-data-with-add-ons/splunk-connect-for-kafka/2.2/overview/data-ingestion-parameters-for-splunk-connect-for-kafka), and Set up and use HTTP Event Collector with configuration files (https://help.splunk.com/en/splunk-enterprise/get-data-in/get-started-with-getting-data-in/9.4/get-data-with-http-event-collector/set-up-and-use-http-event-collector-with-configuration-files) in the Splunk documentation.

Wazuh is a free and open source platform used for threat prevention, detection, and response. From 1.0.0 until 4.14.6 and 5.0.0-beta2, HandleSecureMessage() in src/remoted/secure.c passes a pointer inside its stack buffer to ReadSecMSG(), and src/os_crypto/shared/msgs.c decompresses up to OS_MAXSTR bytes at that offset. For an encrypted agent message on TCP port 1514 that expands to 65,536 bytes, os_zlib_uncompress() writes a terminating null byte beyond the end of the destination buffer. The resulting stack out-of-bounds write in the root-level remoted daemon can crash message processing and disrupt agent communications. This issue is fixed in versions 4.14.6 and 5.0.0-beta2.

IBM Power Systems Firmware FW1120.00, FW1110.00 through FW1110.30, FW1060.00 through FW1060.80, FW950.00 through FW950.H2, OP940.00 through OP940.a1 (Power9), and OP940.00 through OP940.81 (Power HMC) is affected by a vulnerability in the interface between the BMC/FSP and the host system. An attacker with service account or root access to the BMC/FSP can read and write arbitrary regions of host system memory, giving full control over the host system and all hosted partitions, resulting in a confidentiality, integrity, and availability impact.

An OS command injection vulnerability exists in the web management interface of Archer C20 v6 firmware when processing certain WAN-related configuration operations. An authenticated administrator may exploit insufficient input validation to execute arbitrary system commands, potentially resulting in full device compromise. Successful exploitation may allow arbitrary command execution with elevated privileges, compromising the confidentiality, integrity, and availability of the affected device and network traffic passing through it.

In Splunk Enterprise versions below 10.4.2, 10.2.6, 10.0.9, and 9.4.14, a user that holds a role with the rest_properties_get capability could read encrypted stored credentials through the Representational State Transfer (REST) API. Successful exploitation can expose relevant data protected by the stored credentials. The incorrect permission assignment is possible because the properties REST endpoint requires the rest_properties_get capability instead of the list_storage_passwords capability to read stored credentials. For more information see Define roles on the Splunk platform with capabilities (https://help.splunk.com/en/splunk-enterprise/administer/manage-users-and-security/10.4/manage-splunk-platform-users-and-roles/define-roles-on-the-splunk-platform-with-capabilities) in the Splunk documentation.

IBM PowerVM Hypervisor FW1120.00, FW1110.00 through FW1110.30, FW1060.00 through FW1060.80, and FW950.00 through FW950.H2 is affected by a vulnerability in the PowerVM hypervisor call interface. An attacker with root access to a guest partition can issue a specially crafted hypervisor call causing a virtual processor to become permanently unresponsive, requiring a full platform re-IPL to restore normal operation. In some cases this may also cause the guest to inject a small amount of data into hypervisor or partition memory with no attacker control over the target location. Successful exploitation results in an integrity and availability impact to the managed system.

OpenEMR before 8.3.0 contains a path traversal vulnerability in the EDI archive restore function. The archrestore_sel POST parameter is passed to the archive restore handler without sanitization for path traversal sequences. The handler checks whether the supplied path exists on the filesystem, and the differing response messages leak whether the target path exists. An authenticated user with EOB Data Entry permissions can probe arbitrary filesystem paths on the server to determine file existence.

phpMyFAQ before 4.1.7 stores password reset tokens in a publicly accessible tracking file when user tracking is enabled. Unauthenticated attackers can read the tracking file at content/core/data/trackingDDMMYYYY to extract reset tokens and replay them against the password reset API to take over user accounts.

In Splunk Enterprise versions below 10.4.2, 10.2.6, 10.0.9, and 9.4.14, and Splunk Secure Gateway versions below 3.10.10, 3.9.24, and 3.8.71, a user who holds a Splunk role with permissions to list storage passwords but does not hold Splunk Secure Gateway administration privileges could access Mobile Device Management signing secrets that compromise all affected mobile-device enrollment trust through Splunk Secure Gateway. The vulnerability is possible because Splunk Secure Gateway Representational State Transfer (REST) API endpoints for deployment bundle, Security Assertion Markup Language setup, and companion app workflows do not require Splunk Secure Gateway administration privileges before processing requests.

In Splunk Enterprise versions below 10.4.2, 10.2.6, 10.0.9, and 9.4.14, a user who holds the "power" Splunk role could store attacker-controlled Search Processing Language (SPL) in a Table Editor dataset and share the dataset. A user who holds the "admin" Splunk role triggers the SPL when that user opens the dataset in the Table Editor. The SPL runs using the permissions of the second user and could expose all relevant data and modify limited data on the search head. The vulnerability is possible because the Table Editor does not apply SPL safeguards for risky commands when it prepares the dataset initial data. The vulnerability requires the attacker to phish the affected user by tricking them into initiating a request within their browser. The user who holds the "power" Splunk role should not be able to exploit the vulnerability at will. For more information see Define initial data for a new table dataset (https://help.splunk.com/en/splunk-enterprise/manage-knowledge-objects/knowledge-management-manual/9.4/create-and-edit-table-datasets/define-initial-data-for-a-new-table-dataset), SPL safeguards for risky commands (https://help.splunk.com/en/splunk-enterprise/administer/manage-users-and-security/10.2/best-practices-for-splunk-platform-security/spl-safeguards-for-risky-commands), and Define roles on the Splunk platform with capabilities (https://help.splunk.com/en/splunk-enterprise/administer/manage-users-and-security/10.4/manage-splunk-platform-users-and-roles/define-roles-on-the-splunk-platform-with-capabilities) in the Splunk documentation.